Customer Reviews

Absolutely amazing. So nice to be able to talk to the people who know their products inside out. Super Silent generator A⭐️. So quiet.

I contacted your company with a view to part exchange my 10-year old MIG for a new machine. I was pleasantly surprised by the response, which was to have my old faithful serviced. I am extremely pleased with the results, it came back looking like new and is performing brilliantly. 

Chris is absolutely over the moon with the Sabre 100 Plasma Cutter. It came to us on demo and it never went back. I think that speaks for itself. All products can be found on the Warrior Welders Facebook page and their customer service is second to none. You know what they say – you’re only as good as your equipment…  Our Sabre 100 is cutting 25mm Hardox – it’s notoriously hard to cut but with this plasma it cuts like butter and not a single cut edge crack!

The Warrior Cut 100 is a terrific bit of kit. I’m very impressed. My previous machine was a toy compared. 20mm bucket blade and 10mm plate. Like a knife through butter.

A couple of years ago I needed a new welder in a pinch as mine died in the middle of a job. I called Phil and his team, who stayed open so that I would have time to travel and collect a 250A MIG welder. Two years later, it’s been absolutely flawless and welds brilliantly. When my cheap plasma cutter died I knew exactly where to source a new machine and, after a phone call, I collected my new 80A plasma cutter. I was not disappointed and the new machine performs perfectly. I’d recommend Warrior equipment to anyone. If you’re in any doubt pop over and try the machines. They let you try the very machine you’ll be taking home so you know that it’s right before you leave.

Received delivery of the 350 Single-Phase MIG this morning, thank you. Have run it off our geny and, I must say, that is an impressive bit of kit for a 240V welder. And, after putting it through its paces, it certainly lives up to its name… proper little “WARRIOR”. It ran faultlessly on a 10-hour shift, running 1.2 hardfacing cored wire, until we ran out of wire then ran it on 1.6 wire, which is all we had left. A little tweak with the rollers and it just carried on and on. Would definitely recommend this little gem.

I used to own the Warrior 250 MIG until financial struggles required me to sell it. Since then I have had a few machines, none of which came close. The Warrior is by far the best machine out there, and if I had the total amount, I would not hesitate, as I loved my machine. The smoothest, best quality weld money can buy. They can keep those Esabs, Millers and Lincolns. Give me a Warrior any day.

This little 250 MIG welder is more than capable welding 25mm thick steel and is easy to move to difficult locations. I carry out maintenance at a recycling company and this machine has proved invaluable with a wide variety of repair and fabrication work. With the wire removed it is light and compact enough to take it up on the narrow walkways, and a long gas pipe reaches the ground. These machines require a good power supply, and we use a 32 amp single phase socket. Many thanks for a superb machine.

In my workshop I am the ‘newbie’ to welding as I have only been doing it for 20 years. John has been welding since he left school at 16 and Paul about the same, so combined we have around 100 years of welding experience and we can honestly say that the 250 Single-Phase MIG is the best welder we have used, in terms of power, control and simplicity of use. So much so that we were looking to replace our over complicated TIG with one of your Ali MIG set ups

We came across your company on the website as we were looking for a specific machine. The machine recommended to us (250 Single-Phase MIG) was perfect for our application. The transaction and information were excellent from your team as was the delivery to our workshop. We at Castles would definitely purchase again and would recommend Warrior Welders to other Engineering Companies.

Just got back from picking up my new Cut100 plasma cutter from Warrior Welders. I’ve been looking at plasma cutters for a long time now and I phoned and spoke to Phil and, after running through all the information and my requirements, we decided on the Cut 100. They didn’t have one in stock but within a week of the first phone call they had built me one up and it was ready to be collected. I went up today and tried it on some 30mm plate to make sure it was suitable for the work I do, which it is more than enough. I was shown how to use the machine and given plenty of tips and tricks to do with the machine. From start to finish Warrior Welders has been a pleasure to deal with and very knowledgeable within their line of work. I would definitely recommend them to anyone and I know this definitely won’t be my last dealings with Warrior Welders.

Purchased one of your Warrior 350 MIG single-phase welders a number of weeks ago. I was quite sceptical and made a couple of enquiries to others who already have these welders as I hadn’t heard of Warrior before and they were very pleased with them. When it arrived I unpacked it and set into welding (1mm wire). I was blown away with the power of this little Warrior for a single-phase machine. Comes with heavy duty little casters and is so manoeuvrable and flexible around the workshop floor… a pleasure to weld with. I’m a fabricator by trade and can see the quality and workmanship that went into building these machines. I cannot fault them in any way and Phil was a pleasure to deal with!! Keep up the good work lads.

Always very helpful with all my odd requests 🙂 Very knowledgeable team. I’m very fortunate to have them as my supplier. Thanks again.

I have only had my 170 MIG for about a week but am so far very happy with it. When I was looking for a new welder I had narrowed the choice down to Warrior and one other. I phoned them up to check a few details and they were so helpful and friendly I ordered on the spot! The machine is not flashy but very well-built and comes with quality accessories, e.g., the earth lead is thick and heavy (25mm2) and the clamp is massive. Good quality regulators and so on. This is the smallest welder Warrior make but it is clearly built for serious work – more than good enough for me! The ability to phone the company and talk to the actual people who built my machine is fantastic.

We recently bought a Warrior 330 MIG welder which, after two weeks of trialling, we are extremely satisfied with. Our visit to the premises was an enjoyable experience and the whole transaction was easy and hassle free. We were treated in a friendly and welcoming fashion by Phil and got good instruction from Pete in the operation and usage. We’re very pleased with our purchase and would recommend anyone to them without any problem.